Civic-EG.com Forum 3.3.1

- Mon Jun 02, 2008 12:38 pm #57301

My 1st eg build up -> http://civic-eg.com/viewtopic.php?t=802

- Fri Jun 27, 2008 10:36 am #59943

- Fri Jun 27, 2008 2:14 pm #59952 Haha yeah i forgot to update this thread

Bought a new Exedy clutch and flywheel so put that on









Then on monday since uni is over for the summer i started taking mine to bits!







Took the dash out yesterday so i can put in the new OBD1 loom



Oh, and just for Fresh EH2...

My 1st eg build up -> http://civic-eg.com/viewtopic.php?t=802

- Fri Jun 27, 2008 3:03 pm #59960

- Fri Jun 27, 2008 3:57 pm #59971

My 1st eg build up -> http://civic-eg.com/viewtopic.php?t=802

- Wed Jul 02, 2008 8:50 am #60470 Swapped in the new OBD1 interior loom the other day, had to get right at the firewall meaning all the pedals and heater matrix etc had to go! Took a while but wasn't as difficult as i thought it would be



Put the new loom in along with the new p28 ecu and it actually works! Need to add in some more wires to the loom for various things and remove parts of it too so nowhere near finished yet



Also got the exhaust off eventually, its a mess - couldn't separate the sections so just dropped it off in one go





Just got to get the bitchpin out the gear linkage and it'll be bye bye crappy engine

My 1st eg build up -> http://civic-eg.com/viewtopic.php?t=802

- Wed Jul 02, 2008 12:12 pm #60476 nice clutch and fly

- Wed Jul 02, 2008 12:15 pm #60478 Changing looms looks so damn confusing, wires everywhere. When I get a knot in a string, I cut it. Reason you'll never catch me doing shit like this.

Hats off to you sir.

I see you're repping a Halfords battery

Now you have an excuse to get a JDM cat, Spoon B pipe and N1

- Wed Jul 02, 2008 5:46 pm #60512

My 1st eg build up -> http://civic-eg.com/viewtopic.php?t=802

- Mon Jul 07, 2008 5:30 pm #61126 Did some more work today, took off the gear linkages and the 3 lower engine mounts - they need replaced though









Just need to borrow my friends engine crane now and get that sucker out

My 1st eg build up -> http://civic-eg.com/viewtopic.php?t=802

- Wed Jul 09, 2008 11:47 am #61392 Fook doing the wiring loom, i wouldn't know where to start, keep up the great work mate, and i wanna see it in the flesh once its done ya slut!

- Wed Jul 09, 2008 12:13 pm #61402 If it ever runs again then im sure you'll see it

The wirings actually been okay so far surprisingly, i really wasnt looking forward to it

My 1st eg build up -> http://civic-eg.com/viewtopic.php?t=802

- Fri Jul 25, 2008 9:28 pm #63392

- Sat Jul 26, 2008 2:37 pm #63432 Haha thanks mang, the green is definetaly staying

Might aswell update this again!! Been working away quite alot recently, the engine bay was a complete mess







Started working on the slam panel a couple weeks ago, ground every bit of rust off it and primed it with red oxide primer, hopefully that will keep it rust-free for a while!!





Then last week or 2 weeks ago, cant remember, i got the engine out at last - just dropped it on the floor and pulled it out under the car



Since then been working loads grinding away every bit of rust - there was so much, getting there though so will post more photos once its all in primer

My 1st eg build up -> http://civic-eg.com/viewtopic.php?t=802

- Sun Jul 27, 2008 4:52 pm #63504 Very nice project keep up the good work

And dropping the engine through the bottom was something I was going to suggest when reading but heck you beat me to the punch.

Goodluck with the swap

1980 volvo 242
2001 crv
not using punctuation or good sentence structure since day 1