- Sat Apr 09, 2011 5:47 pm
#249311
- Sat Apr 09, 2011 10:14 pm
#249353
- Thu Apr 14, 2011 2:12 pm
#250392
- Fri Apr 15, 2011 5:30 pm
#250588
Not sure I won't have much use for them as everything is braided only car but it may work as a clucth delet line would just need a female to female connector
- Tue Apr 19, 2011 12:29 pm
#251150
Got down to my unit again yesterday so started doing some of the little bits that will need to be done at one point anyway.
So after re-reading teal's shaved engine thread and seeing people asking about a window washer bottle and where he put his I thought I'd do a how to for a custom smaller one.
Do excuse some of the pic's for being upside down not sure how this has happened and can't bothered to change them right now.
Right so want to go from a normal washer bottle to something smaller.
I'm using a spare rad over spill bottle I have but other things can be used, you'll need to stripe the pump and hose from your washer bottle and have them to hand to mock up your new bottle.
First decide where your going to place it.
Drill a guide hole.
Now you'll need to enlarge the hole to fit the pump, don't go to crazy as you need a tight fit to stop leaks.
And test fit to make sure it fits.
I used a knife to clear out any sharp edges melted plastic from drilling.
then checked again with the rubber seal on the pump.
Then fitted the seal in place.
Then fitted the pump into the seal as so
Then secured the pump with cable ties just so it doesn't fall out when driving.
And test fitted it in place out the way but still will have access to refill when needed.
Total cost about 5p for the cable ties job done
So after re-reading teal's shaved engine thread and seeing people asking about a window washer bottle and where he put his I thought I'd do a how to for a custom smaller one.
Do excuse some of the pic's for being upside down not sure how this has happened and can't bothered to change them right now.
Right so want to go from a normal washer bottle to something smaller.
I'm using a spare rad over spill bottle I have but other things can be used, you'll need to stripe the pump and hose from your washer bottle and have them to hand to mock up your new bottle.
First decide where your going to place it.
Drill a guide hole.
Now you'll need to enlarge the hole to fit the pump, don't go to crazy as you need a tight fit to stop leaks.
And test fit to make sure it fits.
I used a knife to clear out any sharp edges melted plastic from drilling.
then checked again with the rubber seal on the pump.
Then fitted the seal in place.
Then fitted the pump into the seal as so
Then secured the pump with cable ties just so it doesn't fall out when driving.
And test fitted it in place out the way but still will have access to refill when needed.
Total cost about 5p for the cable ties job done
- Tue Apr 19, 2011 12:36 pm
#251153
Also got a chance to test fit and check all my break hoses as Hel sent through the right length hoses the other day so put the rears in place.
Then ran these through the car and did the same with my braided fuel line.
Will need to mod my fuel tank cover to allow all the hoses to run through here at some point.
Then stared putting the lines to the slave cylinder and figuring out where its going to be mounted
This now means that I only have braided lines on the car now for all my breaks
And total off topic but not sure if you guys get these sweet over there but I'm addicted to them and love the packaging
I'll take pics of the other flavours next time I get some.
Then ran these through the car and did the same with my braided fuel line.
Will need to mod my fuel tank cover to allow all the hoses to run through here at some point.
Then stared putting the lines to the slave cylinder and figuring out where its going to be mounted
This now means that I only have braided lines on the car now for all my breaks
And total off topic but not sure if you guys get these sweet over there but I'm addicted to them and love the packaging
I'll take pics of the other flavours next time I get some.
- Tue Apr 19, 2011 10:04 pm
#251229
- Sun Sep 11, 2011 12:36 am
#271280
http://civic-eg.com/viewtopic.php?t=17296
My for sale thread check it out!
http://www.civic-eg.com/viewtopic.php?t=25828
#3 CivicEG.com Ferio Squad
My for sale thread check it out!
http://www.civic-eg.com/viewtopic.php?t=25828
#3 CivicEG.com Ferio Squad
- Sun Oct 02, 2011 10:10 am
#275732
Right quick update sorry no pics as haven't put them on my pc yet but she lives.
Turned her over for the first time on Thurs and after a cough and splutter she lives again. As I have taken out the charcoal canister I've got a check light coming up and so far not found any fixes for this so may need to reinstall the canister.
Other than that is running sweet just playing with ride hight to get the right then gonna get my camber set up done.
Next is a full valet just intime for winter weather and start on getting the interior sprayed and tidy.
Will get some pics up real soon
Turned her over for the first time on Thurs and after a cough and splutter she lives again. As I have taken out the charcoal canister I've got a check light coming up and so far not found any fixes for this so may need to reinstall the canister.
Other than that is running sweet just playing with ride hight to get the right then gonna get my camber set up done.
Next is a full valet just intime for winter weather and start on getting the interior sprayed and tidy.
Will get some pics up real soon
- Mon Oct 03, 2011 3:41 pm
#275934