Do Not PM me your technical questions. Post them in the forum!
My 1992 SOHC Turbo Hatch
My Youtube Channel: 6th Gear Garage
My 1992 SOHC Turbo Hatch
My Youtube Channel: 6th Gear Garage
- Mon Aug 06, 2012 2:55 pm
#312920
You need a custom title for this amazing build
- Mon Aug 06, 2012 10:20 pm
#312949
this has been an trial and error day , 60% off my plans has gone to the bin 
but with a less sense and a bigger hammer u can fix anything they say .. 
i was going to make a one piece brace but my bending machine did not allow me to , so i changed that plan...
this is the end result..
and now she sits on all four again ...
does not look like i did much do day but it has been a p.i.t.a all day
but with a less sense and a bigger hammer u can fix anything they say ..
i was going to make a one piece brace but my bending machine did not allow me to , so i changed that plan...
this is the end result..
and now she sits on all four again ...
does not look like i did much do day but it has been a p.i.t.a all day
Last edited by Gunni on Fri Nov 23, 2012 4:59 pm, edited 1 time in total.
- Tue Aug 07, 2012 8:47 am
#312973
If you really think about it I'd say you've done loads seeing as you have the new frame in place which is a big leap forward.
Loving the total sleeper look of this.
Loving the total sleeper look of this.
- Wed Aug 08, 2012 7:09 pm
#313071
stripped out the old D motor out today..
some faggot stole the brake master cil, and proportion valve and lines while it was outside ...
the gearbox reddy ...
put it in for a quick look, does not seem to be a much moddification needed so far, but i have to drop in a dummy motor as well to bee shure
i think i lost the crv gearbox bracket , i cant find it, so this is the only thing needed modding so far.... hope im right
some faggot stole the brake master cil, and proportion valve and lines while it was outside ...
the gearbox reddy ...
put it in for a quick look, does not seem to be a much moddification needed so far, but i have to drop in a dummy motor as well to bee shure
i think i lost the crv gearbox bracket , i cant find it, so this is the only thing needed modding so far.... hope im right
Last edited by Gunni on Fri Nov 23, 2012 5:02 pm, edited 1 time in total.
- Thu Aug 09, 2012 4:54 pm
#313150
thing are coming along nicely ...
will start on shifter cables and rear diff and shaft soon, but i have to set this on hold until monday , racing my eg on saturday in rallycross , cant miss that
will start on shifter cables and rear diff and shaft soon, but i have to set this on hold until monday , racing my eg on saturday in rallycross , cant miss that
Last edited by Gunni on Fri Nov 23, 2012 5:18 pm, edited 1 time in total.
- Sat Aug 11, 2012 6:22 am
#313271
Its coming out well, Looks like you wont have to make any changes to the drive shafts which is good. I bet your exicted, I know I would be if I was you right now.
Good work.
Its coming out well, Looks like you wont have to make any changes to the drive shafts which is good. I bet your exicted, I know I would be if I was you right now.
Good work.
- Wed Aug 15, 2012 11:24 am
#313547
not much work done yesterday ,but i have to get this rolling at the end of this month so...
made a diff holding bracket using bits from this..
poly bushings ..
i wish i had a water cutting machine
should look something like this , im not as happy with it as i hoped to ,but i can always make some thing better later .
peace and quiet
made a diff holding bracket using bits from this..
poly bushings ..
i wish i had a water cutting machine
should look something like this , im not as happy with it as i hoped to ,but i can always make some thing better later .
peace and quiet
Last edited by Gunni on Fri Nov 23, 2012 5:20 pm, edited 1 time in total.
- Wed Aug 15, 2012 1:13 pm
#313554
subscribed, good stuff so far.