looks like a nice clean hatch!!!
- Thu May 07, 2009 2:02 am
#115404
cali cars FTW!!!! ............... bare metal rusts overnight here. looks like a nice clean hatch!!!
looks like a nice clean hatch!!!
- Thu May 07, 2009 9:42 pm
#115531
if u have any questions i will be happy to answer them..these are the tools im using
1. step remove, plastic cover,,only 3screws.
2.step,remove two size 10bolts, and remove the metal piece.
step.3 find the wires ur going to be using. make sure u do some research on wire color of ur car. this is my list....#1.constant=white(+)..#2.starter=black/white(+)..#3.ignition=black/yellow(+)..#4.parking ligths=red/black(+)..#5.trunk=green(-)..#6.doors pins=green/red(-)..#7.horn=blue/red(-)..#8.domeligth=green/red(-).
4. after i got the location of all the wires i was going to be using..i install the LED, make sure u drill a hole for ur led in a place or part that u can
easily replace.
im installing the siren since i dont like to drill hole on my car i use an xcinting hole.
also install a hood pin, the more protection the better.
5.i started to assmble al the plugs into the alarm, like the led,valet,ect.
i use some tape so thiefs dont see any color wires or the alarm.
6. find a good place for the alarm,
7. once u have the list of ur wirring and location start connecting ur wires..
here u will find all ur 12v,constant,ignition,starter,also the horn,parking light
this is a demostration of how i connected all my wires. u can do it any way u feel its safe.. i use tape because i will be removing this alarm later in the future.. this white plug with the blue/green wire is the horn.
8. after u connect all ur wires and make sure everything works u can use more tape so there is no evidence of ur alarm,,
9. my alarm came with an antena for better range, make sure u install the antena one inch away from any metal.
10. on ur left side,(kickpanel) u will find the wires for ur doors,domeligth,and trunk.. also this is were im going to be putting my relay for my locks.
all done,
next i will be installing the powerdoorlocks
1. step remove, plastic cover,,only 3screws.
2.step,remove two size 10bolts, and remove the metal piece.
step.3 find the wires ur going to be using. make sure u do some research on wire color of ur car. this is my list....#1.constant=white(+)..#2.starter=black/white(+)..#3.ignition=black/yellow(+)..#4.parking ligths=red/black(+)..#5.trunk=green(-)..#6.doors pins=green/red(-)..#7.horn=blue/red(-)..#8.domeligth=green/red(-).
4. after i got the location of all the wires i was going to be using..i install the LED, make sure u drill a hole for ur led in a place or part that u can
easily replace.
im installing the siren since i dont like to drill hole on my car i use an xcinting hole.
also install a hood pin, the more protection the better.
5.i started to assmble al the plugs into the alarm, like the led,valet,ect.
i use some tape so thiefs dont see any color wires or the alarm.
6. find a good place for the alarm,
7. once u have the list of ur wirring and location start connecting ur wires..
here u will find all ur 12v,constant,ignition,starter,also the horn,parking light
this is a demostration of how i connected all my wires. u can do it any way u feel its safe.. i use tape because i will be removing this alarm later in the future.. this white plug with the blue/green wire is the horn.
8. after u connect all ur wires and make sure everything works u can use more tape so there is no evidence of ur alarm,,
9. my alarm came with an antena for better range, make sure u install the antena one inch away from any metal.
10. on ur left side,(kickpanel) u will find the wires for ur doors,domeligth,and trunk.. also this is were im going to be putting my relay for my locks.
all done,
next i will be installing the powerdoorlocks
Last edited by leeb18c on Wed Oct 19, 2011 10:17 pm, edited 7 times in total.
